Sym Quad Raider 600 Service Manual Download Page 174

Page: 174 / 247

To this chapter contents

14. BODY COVER

Maintenance

Body covers disassemble sequence:

Front Carrier

Maintenance Cover

Front Top Cover

Fuel Tank Cover

Front Grille

R/L Inner Protector

Front Low Bumper

Front Fender

R/L Side Covers

Front Bumper Cover

Rear Center Up Cover

Tail Light Low Cover

Rear Carrier

Rear fender

Be careful not to damage various covers in assembly or disassembly operation.

Never injure hooks molded on the body covers.

Align the buckles on the guards with slot on the covers.

Make sure that each hook is properly installed during the assembly.

Never compact forcefully or hammer the guard and the covers during assembly.

14-2

Summary of Contents for Quad Raider 600
























































































































































































































































Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands

Sym Quad Raider 600, Service Manual

Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands