Sym Quad Raider 600 Service Manual Download

Page: 188 / 247

15. FRONT BRAKE & FRONT WHEEL

To this chapter contents

Front Brake Caliper

Removal

Place a container under the brake caliper, and
loosen the brake hose bolt and finally remove the
brake hose.

Caution

Do not spill the brake fluid on painted surfaces.

Remove two caliper bolts and the caliper.

Inspection

Make sure the brake linings condition. Replace the
linings if the brake linings wear limitation groove
close to the brake disk.

Brake lining replacement

Remove two guide pins.
Compress caliper-mounting plate, and then
remove brake linings.
Install new linings, and tighten the guide pins.

Installation

Install the brake caliper and tighten the attaching
bolts securely.

Torque: 3.25kgf-m

Caution

Use M8 x 20 mm flange bolt only.

Long bolt will impair the operation of brake
disk.

Use two seal washers and hose bolts to lock the
hose and brake caliper in place.

Torque: 3.5kgf-m

Refill up the brake fluid to the reservoir and make
necessary air bleeding.

Brake hose bolt

2 bolts

Guide pins

15-8

Summary of Contents for Quad Raider 600
























































































































































































































































Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands

Sym Quad Raider 600, Service Manual

Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands