manualshive.com logo in svg

Sym Quad Raider 600, Service Manual

Share
Download
Sym Quad Raider 600 Service Manual Download Page 108

8. V-BELT DRIVING SYSTEM 

 

8-16

 

Installation 

Use the driven face assy. expander to expand the 
driven face assy. 
Put the drive belt into the driven face assy. and 
hold it tight by hand. 

 

Special Tool 
Tool number: SYM-2321000-REA 
Tool name: Driven Face Assy. Expander

 

 

 

Put the driven face assy. onto the drive shaft. 
 

 Caution 

 

Use special tool to keep the driven face           
assy. open.   

 

Do not oppress friction plate in order to 

avoid distortion or damage. 

 
 
 

Install the movable drive face assy. 
Hold the movable drive face assy. with the MDF 
holder, and then tighten nut to specified torque 
value. 

Torque value: 8.5~10.5kgf-m 

 

 

 

 

 

 

 

Hold the driven face with universal holder, and 
then tighten nut to specified torque value. 

Torque value: 5.0~6.0kgf-m 

 

 

 

 

 

 

 

Driven Face Assy.

To this chapter contents 

To this chapter contents 

 

Driven Face Assy. Expander

 

 

Universal holder

 

Drive Shaft 

Summary of Contents for Quad Raider 600
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands