manualshive.com logo in svg

Sym Quad Raider 600, Service Manual

Share
Download
Sym Quad Raider 600 Service Manual Download Page 205

 

16. STEERING / FRONT SUSPENSION 

16-13

 

 

Toe-In 

After repair or disassembly of the steering system 
parts, adjustment of toe-in is required. 
Keep the vehicle on level ground and the front 
wheels facing forward. 

Mark the centers of the tires to indicate the axle 

center height. 

Measure the distance between the marks. 
 
 

 

 

 

 

Move the vehicle back carefully and let the wheels 

turn 180 degree, so the marks on the tires are 

aligned with the axle center height. 

Measure the distance between the marks. 

Calculate the difference in the front and rear 

measurements. 

 

Toe-in: 5±10mm 

 

 

 

 

 

 

 

If the toe-in is out of standard, adjust it by hanging 

the length of the tie-rods equally by turning the 

tie-rod while holding the ball joint. 
Loosen two side tie-rod lock nuts; turn the tie-rods 
to adjustment toe-in. 

Tighten the lock nuts. 

Torque value: 3.6kgf-m 

 

 

 

 

 

 

 

To this chapter contents 

Lock

Adjustment 

Summary of Contents for Quad Raider 600
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands