manualshive.com logo in svg

Sym Quad Raider 600, Service Manual

Share
Download
Sym Quad Raider 600 Service Manual Download Page 164

13. COOLING SYSTEM 

 

13-6 

 

Check reserve tank 

 

Remove the front center cover, and then 
remove reserve tank filler cap. 

 

Check the liquid level in the front fender right 
side. Add coolant to proper level if too low. 

 

Reinstall the reserve tank filler cap. 

 Caution 

Do not add too much coolant to prevent the 
coolant backflow flooding when the temperature 
rises. 

 
 

Radiator 

Check 

Remove the front center cover, side covers and 
front fender. 

(Refer to chapter 13)

, check for any 

leakage from weld seam. 
Blow the radiator fins with compressed air. If the 
radiator is blocked by dirt, use low-pressured 
water jet to clean it. 
Be careful straightening the radiator fins. 
 
 
 

 
Removal 

Remove the radiator outlet hose to drain out the 
coolant. 
 
 
 
 
 
 
 
 
 
 

 

Remove the radiator hose clamp and hose. 

 

 

 

 

 

 

 

 

Upper 

Radiator hose 

To this chapter contents 

Lower 

Clamp

Radiator outlet hose 

Clamp

Summary of Contents for Quad Raider 600
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands