Sym Quad Raider 600 Service Manual Download Page 194

Page: 194 / 247

16. STEERING / FRONT SUSPENSION

16-2

Precautions in Operation

Torque Values

Handlebar upper holder bolt

2.4kgf-m

Handlebar under holder nut

4.0kgf-m

Steering shaft holder bolt

3.4kgf-m

Steering shaft nut

5.0kgf-m

Steering tie-rod nut

5.0kgf-m

Knuckle nut

5.0kgf-m

Tie rod lock nut

3.6kgf-m

Suspension arm nut

5.0kgf-m

Front

cushion mounting nut

4.6kgf-m

Trouble Diagnosis

Hard to steer

Faulty tire.

Steering shaft holder too tight.

Insufficient tire pressure.

Faulty steering shaft bushing.

Damaged steering shaft bushing.

Front wheel wobbling

Faulty tire.

Worn front brake drum bearing.

Bent rim.

Axle nut not tightened properly.

Steers to one side

Bent tie rods.

Wheel installed incorrectly.

Unequal tire pressure.

Bent frame.

Worn swing arm pivot bushings.

Incorrect wheel alignment.

Front suspension noise

Loose front suspension fasteners.

Binding suspension link.

Hard suspension

Faulty front swing arm bushings.

Improperly installed front swing arms.

Bent front shock absorber swing rod.

Soft suspension

Weak front shock absorber springs.

Worn or damaged front swing arm bushings.

To this chapter contents

Summary of Contents for Quad Raider 600
























































































































































































































































Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands

Sym Quad Raider 600, Service Manual

Search results

Summary of Contents for Quad Raider 600

Reviews:

Related manuals for Quad Raider 600

Brands by name

Popular brands