manualshive.com logo in svg

Sym Quad Raider 600, Service Manual

Share
Download
Sym Quad Raider 600 Service Manual Download Page 195

 

16. STEERING / FRONT SUSPENSION 

16-3

 

 

Steering Handle 

Removal 

Remove the handle cover, meter set, handle 
protect cover and front fender. (Refer to chapter 
13) 
Remove the handle wire band. 
 
 
 
 
 
 
 
 
Loosen the socket bolts from the rear brake 
master cylinder, and remove front brake master 
cylinder. 

 Caution 

Do not let foreign materials enter the brake 
master cylinder. 

Remove 2 screws, and then remove throttle 
hosing holder and throttle hosing. 
Loosen 2 screws, and then remove handle left 
switch and choke hosing. 
 
 
 
Loosen 2 screws, and then remove 2&4 wheel 
drive change switch. 
 
Loosen the 2 socket bolts for the front brake 
master cylinder, and remove front brake master 
cylinder. 

 

 Caution 

Do not let foreign materials enter the brake 
master cylinder. 

 
 
 
Loosen the 2 screws for throttle hosing holder and 
remove throttle hosing. 
 
 

 

 

 

 

 

 

 

To this chapter contents 

2 

2 screws

2 brocket bolts 

Handle lift 

Handle wire 

2 brocket bolts 

Summary of Contents for Quad Raider 600
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands