Stryker 3002 Maintenance Manual Download Page 49 | Manualshive

Page: 49 / 245

background image

Return To Table of Contents

www.stryker.com

3006-409-006 REV C

49

TOOLS REQUIRED:

• 5/16” Nut Driver
• T27 Torx

PROCEDURE:

1. Run the Knee Gatch fully up.
2. Using a T27 Torx, remove the screw holding the midsection litter access covers to the litter and remove the

covers.

3.  Run the head section down electrically until flat (0) or use the CPR release handle to fully lower the head.
4.  Lightly tap the Fowler down button until the bolt and bushing (E) are centered in the slot.
5.  Unplug the power cord from the wall socket.
6.  Using a 5/16” nut driver, loosen the two screws (A) on the cam (B).
7.  Slide the cam toward the head of the bed just until the micro-switch is activated (the switch will make a clicking

noise).

Note

Check that the cam “bump” is on the “head” side of the switch actuator.

8. Tighten the two screws (A).

CAUTION

Be sure the head section stops when it is fully up and the ball nut bracket (C) is approximately 3/4” from panel (D). If
not, damage to the unit could result.

9. Ensure the head section will lower to flat (0) before returning the bed to service. Verify the head section lowers

onto the rubber rests and the motor stops running. Reinstall the litter access panels removed in step 1.

LIMIT SETTING - FOWLER MOTOR

E

B

A

D

C

Service Information

«
...
47
48
49
50
51
...
»

Summary of Contents for 3002






















































































































































































































































Reviews:

No comments

Related manuals for 3002

Brand: Haki Pages: 24

Brand: Dakota Digital Pages: 5

Brand: Xiitech Pages: 6

Brand: Macht Dental Pages: 8

Brand: Rainin Instrument Pages: 16

Brand: Pari Pages: 282

Brand: A&D Pages: 29

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Brand: M-Audio Pages: 25

Brand: Kellfri Pages: 44

SimNewB Anomaly Set

Brand: laerdal Pages: 10

Fusionchef pearl

Brand: Julabo Pages: 43

Brand: Nuvo Pages: 2

Brand: unix Corporation Pages: 6

GYRONETICS E-Series

Brand: gorilla sports Pages: 22

Brand: Cameo Pages: 188

Brand: Calex Pages: 17

Brand: Synca Pages: 12

ELITE Ragley Pro Comfort

Brand: Quest Leisure Products Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands