manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 135

Index

g

A

Accessing the technical compartment . . 107
Address of manufacturer . . . . . . . . . . . . . I
Adjusting the floor . . . . . . . . . . . . . . . . . 41
Adjusting the seat . . . . . . . . . . . . . . . . . 40
Aerosol can for chains . . . . . . . . . . . . . 105

B

Batteries . . . . . . . . . . . . . . . . . . . . . . . . 32
Battery

Closing the battery hood . . . . . . . . . . 88
Opening the battery hood . . . . . . . . . 88
Type . . . . . . . . . . . . . . . . . . . . . . . . . 87

Battery acid . . . . . . . . . . . . . . . . . . . . . . 14
Before picking up a load . . . . . . . . . . . . . 83
Behaviour when driving . . . . . . . . . . . . . 49
Braking . . . . . . . . . . . . . . . . . . . . . . . . . 32
Braking on the version without pedals . . . 34
Braking with the dual-pedal op-

tion . . . . . . . . . . . . . . . . . . . . 36, 72

Braking with the single-pedal option . . . . 35

C

CE labelling . . . . . . . . . . . . . . . . . . . . . . . 3
Changing the side access battery . . . . . . 91
Charging the battery . . . . . . . . . . . . . . . 111
Charging the battery using an external

charger . . . . . . . . . . . . . . . . . . . . 89

Checking the battery acid level and

electrolyte density . . . . . . . . . . . 115

Checking the brakes . . . . . . . . . . . . . . . 34

Single-pedal option . . . . . . . . . . . . . . 67
Without pedals . . . . . . . . . . . . . . . . . 56

Checking the cables, terminals and the

battery connector . . . . . . . . . . . . 116

Checking the condition of the load

arms . . . . . . . . . . . . . . . . . . . . . 112

Checking the condition of the wheels . . 113
Checking the emergency off switch . . . . . 33
Checking the horn . . . . . . . . . . . . . . . . . 37
Checks prior to start-up . . . . . . . . . . . . . 33
Cleaning the truck . . . . . . . . . . . . . . . . 110

Climatic conditions . . . . . . . . . . . . . . . . . . 8
cold store . . . . . . . . . . . . . . . . . . . . . . . . 85
Cold store usage . . . . . . . . . . . . . . . . . . 85
Consumables . . . . . . . . . . . . . . . . . . . . 13

Battery acid safety instructions . . . . . 14
Disposal . . . . . . . . . . . . . . . . . . . . . . 15
Oil Safety Information . . . . . . . . . . . . 13
Safety information for handling

hydraulic fluid . . . . . . . . . . . . . . . . 14

Contact details . . . . . . . . . . . . . . . . . . . . . I
Copyright and property rights . . . . . . . . . . 3

D

Defining directions . . . . . . . . . . . . . . . . . 50
Description of use . . . . . . . . . . . . . . . . . . 8
Destruction . . . . . . . . . . . . . . . . . . . . . 120
Display of the drive wheel position . . . . . . 42
Display operating unit . . . . . . . . . . . . . . . 27
Display unit

Activity indicator . . . . . . . . . . . . . . . . 46
Drive program . . . . . . . . . . . . . . . . . . 46
Error codes menu . . . . . . . . . . . . . . . 47
Operator presence . . . . . . . . . . . . . . 43
Settings . . . . . . . . . . . . . . . . . . . . . . 45
Start-up screen . . . . . . . . . . . . . . . . . 48
Temperature . . . . . . . . . . . . . . . . . . . 45
Warnings . . . . . . . . . . . . . . . . . . . . . 45

Disposing of components and batteries . . . 9
Drive program

Blue Q mode . . . . . . . . . . . . . . . . . . . 60
Hare mode . . . . . . . . . . . . . . . . . . . . 60
Tortoise mode . . . . . . . . . . . . . . . . . . 61

Drive system . . . . . . . . . . . . . . . . . . . . . 32
Driver rights,duties and rules of

behaviour . . . . . . . . . . . . . . . . . . 18

Driver's compartment . . . . . . . . . . . . 24, 32
Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Driving

Dual-pedal option . . . . . . . . . . . . . . . 70
Single-pedal option . . . . . . . . . . . . . . 65
Without pedals . . . . . . . . . . . . . . . . . 53

Driving on loading bridges . . . . . . . . . . 100

11548011751 EN - 10/2018

127

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands