manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 44

4

Use

Checks and actions prior to commissioning

Braking with the dual-pedal option

Braking using the brake pedal
– Press the accelerator pedal (2) or (3) to

move the truck forwards.

– Release the accelerator pedal.
– Press the brake pedal (1).
The truck brakes progressively until the truck

comes to a complete stop.
Braking by releasing the accelerator
– Press the accelerator pedal (2) or (3) to

move the truck forwards.

– Release the accelerator pedal.
The truck brakes progressively until the truck

comes to a complete stop.
Braking by reversing the drive direction
– Press the accelerator pedal (2) or (3) to

move the truck forwards.

– Press the other accelerator pedal.
– Keep the pedal depressed.
The truck brakes progressively and then

moves off in the opposite direction until the

desired speed has been reached.

NOTE

Also ensure that the stabiliser wheels operate

correctly. This influences braking effective-

ness.

36

11548011751 EN - 10/2018

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands