manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 61

Use

4

Driving

Driving with the version without

pedals

DANGER

Risk of serious injury
Always keep your body inside the driver's compart-

ment while the truck is moving.

WARNING

Be aware of the position of the drive wheel.
Slowly start the truck.
Check the position of the drive wheel on the display.

NOTE

Always operate the joystick slowly, as the truck

reacts immediately. Abrupt starts or braking,

or sudden reversal of the drive direction, must

be avoided at all costs.

NOTE

The truck accelerates in proportion to the

pressure exerted on the joystick.

The forklift operator selects the direction of

travel using the joystick. The joystick has two

positions:
• Forward travel (1)
• Reverse travel (2)
– Put the truck into service.
Forward travel
– Push the joystick to the left (1) to travel

forwards (opposite load arm direction)

Reverse travel
– Push the joystick to the right (2) to travel

backwards (load arm direction)

WARNING

Restricted visibility
During reverse travel, visibility may be restricted.

Be very careful. Make sure that the path behind is

clear before travelling in reverse.

11548011751 EN - 10/2018

53

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands