Still FXH 20 Original Instructions Manual Download Page 95

Page: 95 / 140

Use

Handling the battery

Battery type

Trucks can be ﬁtted with different types of

battery. Comply with the information indicated

on your battery's type plate, as well as with its

features.

WARNING

The weight and size of the battery inﬂuence the

stability of the truck.
The new battery must weigh the same as the old

one. Do not remove extra weight or change its

position.

CAUTION

Be careful not to damage any wiring when replacing

the battery.

Order picking

Maintenance personnel

The battery must be replaced by specially

trained personnel. Personnel must follow the

manufacturer's instructions for the battery, the

charger and the truck.
It is also necessary to follow the battery

maintenance instructions.

Fire protection measures

WARNING

Do not smoke or create a ﬂame when

handling batteries. There must be

no combustible material or tools that

produce sparks within a minimum

radius of 2 m around the truck and the

battery charger.
The work area must be well ventilated.

Fire extinguishers must be provided

and located near the work area.

Parking the truck securely

When the battery is being worked on, the truck

must be parked safely. The truck can only be

11548011751 EN - 10/2018

Summary of Contents for FXH 20













































































































































Search results

Summary of Contents for FXH 20

Reviews:

Brands by name

Popular brands

Still FXH 20, Original Instructions Manual

Search results

Summary of Contents for FXH 20

Reviews:

Brands by name

Popular brands