manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 23

Safety

2

Safety regulations for handling consumables

– Dispose of used battery acid in line with the

applicable regulations.

Disposal of consumables

ENVIRONMENT NOTE

Materials that have to be disposed of following

maintenance, repair and cleaning must be

systematically collected and disposed of in

accordance with regulations. Observe the

national regulations for your country. Work

may only be carried out in areas designated

for this purpose. Take care to minimise, as far

as possible, any impact on the environment.

• Any spillage of fluids such as hydraulic oil,

brake fluid or gear lubricant oil must be

immediately soaked up with an oil-binding

agent.

• The regulations for disposal of used oil are

applicable.

• Any spillage of battery acid must be neu-

tralised immediately.

11548011751 EN - 10/2018

15

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands