manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 79

Use

4

Driving: Dual-pedal option

The operator selects the direction of travel

using the accelerator pedals:
• Forward travel (1)
• Reverse travel (2)
Forward travel
– Press the accelerator pedal (1) to move

forwards (in the opposite direction to the

load arms).

Reverse travel
– Press the accelerator pedal (2) to move

backwards (in the direction of the load

arms).

WARNING

Restricted visibility
During reverse travel, visibility may be restricted.

Be very careful. Make sure that the path behind is

clear before travelling in reverse.

Reversing the direction of travel

– Press one of the accelerator pedals (1) or

(2).

– Release the pedal.
– Press the other accelerator pedal.
The truck brakes progressively and then

moves off in the opposite direction until the

required speed has been reached.

11548011751 EN - 10/2018

71

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands