manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 55

Use

4

Using the display-operating unit

Settings menu

It is possible to access different settings

through the Settings menu.
– Select the Settings menu (1)
This menu allows access to a drop-down

menu (2) consisting of:
• Language
• Unit
• Date format
• Date
• Time
• Adjustment of the Load Management

warning sounds

• Adjustment of the contrast
• Adjustment of the brightness
– Select the desired option

Error codes menu

It is possible to access error messages that

are disrupting the operation of the truck.
– Select the Error messages menu (1)
The operator can access the error codes. If

several codes are affecting the truck, the op-

erator can scroll through several successive

displays.
The number of error messages is indicated at

the bottom of the display (2).

11548011751 EN - 10/2018

47

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands