manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 58

4

Use

Driving

Driving

Defining directions

On a ride-on pallet truck, the conventional

controls for the drive direction are:
• Forward travel (2): Opposite direction to the

load arms/forklift operator direction

• Reverse travel (1): Direction of the load

arms

Operation of operator presence

detection on the version without

pedals

DANGER

Risk of serious injury
Always keep your body inside the driver's compart-

ment while the truck is moving.

The truck is equipped with two operator

presence detectors:
• The seat (1)
• The operator presence button on the

adjustable floor (2)

These two components are truck safety

devices.
To activate the operator presence detection,

proceed as follows:
– Sit on the seat (1).
– Press the operator presence button (2).

Keep the pedal depressed before and whilst

the truck is moving.

The truck controls are then available.

50

11548011751 EN - 10/2018

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands