manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 42

4

Use

Checks and actions prior to commissioning

Checking the brakes

NOTE

Braking is progressive and increases as the

brake pedal is depressed.

Braking on the version without pedals

Braking using the brake pedal
– Push the joystick to move the truck for-

wards.

– Press the brake pedal (1).
The truck brakes progressively until the truck

comes to a complete stop.
Braking by releasing the joystick
– Push the joystick to move the truck for-

wards.

– Release the joystick.
The truck brakes progressively until the truck

comes to a complete stop.
Braking by reversing the drive direction
– Push the joystick to move the truck for-

wards.

– Push the joystick in the opposite direction.
The truck brakes progressively and then

moves off in the opposite direction until the

desired speed has been reached.

NOTE

Also ensure that the stabiliser wheels operate

correctly. This influences braking effective-

ness.

34

11548011751 EN - 10/2018

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands