manualshive.com logo in svg

Still FXH 20, Original Instructions Manual

Share
Download
Still FXH 20 Original Instructions Manual Download Page 73

Use

4

Driving: Single-pedal option

CAUTION

Releasing the operator presence button
When the operator presence button is released

when moving:
- The parking brake is activated
- All controls are available

CAUTION

Disabling of controls
When the operator leaves the seat, after a time

delay:
- The parking brake is activated
- The controls are no longer available

Driving with the single-pedal option

DANGER

Risk of serious injury
Always keep your body inside the driver's compart-

ment while the truck is moving.

WARNING

Be aware of the position of the drive wheel.
Slowly start the truck.
Check the position of the drive wheel on the display.

NOTE

Always depress the pedal slowly, as the truck

reacts immediately. Abrupt starts or braking,

or sudden reversal of the drive direction must

be avoided at all costs.

NOTE

The truck accelerates in proportion to the

pressure exerted on the accelerator pedal.

The operator selects the direction of travel

using the drive switch located on the joystick:
• Forward travel (1)
• Reverse travel (2)

11548011751 EN - 10/2018

65

Summary of Contents for FXH 20













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands