Stiga TITAN 26 B, Instructions For Use Manual

Page: 88 / 248

88
ENGLISH
EN
Only fill or top up with fuel outdoors,
and never smoke when filling or
topping up. Fill up with fuel before
starting the engine.
Never remove the fuel cap or fill with
fuel while the engine is running or still
warm.
The engine must not be run on rapeseed
diesel (RME). Contact the engine
supplier for additional information.
Filling fuel up into the filler pipe results
in fuel leakage and risk of fire.
Only use diesel which satisfies the requirements in
“2.1”.
1. Open the fuel cap (4:D).
2. Fill with diesel up to the lower part of the filler
pipe. If fuel is filled up into the filler pipe, fuel
will leak out because it expands when heated.
3. Close the fuel cap.
5.3 LEVEL CHECK, ENGINE OIL
Check the oil level every time before using to
ensure it is correct. The machine should be
standing on level ground.
Check the following:
1. Wipe clean around the oil dipstick (15:K), and
pull it up.
2. Wipe the dipstick.
3. Slide the dipstick down completely and pull up
again.
4. Read off the oil level. The oil level should be up
to the mark (15:L) on the dipstick.
If necessary, remove the oil filler cap (15:J) and fill
up the oil up to the mark.
Use oil grade CF or higher according to API and
according to the temperature diagram below.
Never use oil additives.
The oil level must never exceed the mark (15:L).
This can cause the engine to overheat. Drain the oil
to the correct level if the oil level exceeds the
mark.
Reinstall the oil filer cap once the oil level has
been adjusted.
5.4 LEVEL CHECK, COOLANT
The temperature indicator will not
work if there is no coolant. This results
in engine failure.
Check the coolant level every time before use to
ensure it is correct.
Check the following:
1. The engine must be cold when checking.
2. Remove the right-hand engine cover.
3. Unscrew the radiator cap (13:C) and check that
the coolant level reach the filler hole.
4. Reinstall the radiator cap.
5. Check that the coolant level is at the lower mark
(12:L) in the expansion tank.
If necessary, top up with coolant. See below.
5.4.1 Topping up with coolant
The coolant must meet the following require-
ments:
• Always use a mixture of refrigerant and water.
Never use just water.
• Mix the water and refrigerant according to the
refrigerant supplier’s instructions.
• Never mix different refrigerants.
• Use soft water (no calcium content), distilled or
demineralised water.
The engine must be cold when filling.
If the radiator cap is opened when the
engine is hot there is a risk of serious
burn injuries from hot water that may
spray out.
Top up as follows:
1. Remove the front engine cover.
2. Check that all the plugs in the cooling system
are installed and sealed.
. Check that all the taps in the cooling system are
closed and sealed.
4. Check that all the hoses in the cooling system
are intact and sealed.
5. Unscrew the radiator cap (13:C).
6. Slowly fill the radiator with coolant. Air bub-
bles must not form when filling. Fill up to the
filler hole.
7. Reinstall the radiator cap.
8. Open the cap on the expansion tank (12:K) and
top up the mixture to the lower mark which is
the level when the engine is cold.
9. Close the cap for the expansion tank.
10.Run the engine to operating temperature and
check the level in the expansion tank. The level
should now be at the upper mark (12:T), which
is the level for when the engine is hot.
11.If the level is not up to the upper mark, allow the
engine to cool and then top up with coolant in
the expansion tank.