STERO SD3 Series Service And Parts Manual Download Page 64

Page: 64 / 71

DRAIN UNIT

ILLUS.
PL-60523

PART NO.

NAME OF PART

AMT.

0A-108232

Strainer Pan...............................................................................................................................1

0P-678143

Cotter Pin 1/16 x 1/2 (SST)........................................................................................................1

0A-108189

Axle - Drain Lever.......................................................................................................................1

0A-108244

Drain Lever Assy........................................................................................................................1

0A-108247

Drain - Lift...................................................................................................................................1

0P-678344

Mach. Screw 10-24 x 1/2 Phil. Truss Hd. (SST).........................................................................1

0P-578177

O-Ring........................................................................................................................................1

0A-108241

Drain Tube Assy.........................................................................................................................1

0A-108242

Cover - Standpipe......................................................................................................................1

0P-678355

Washer.......................................................................................................................................3

0P-678349

Self-Tapping Screw 10-24 x 1/2 Phil. Truss Hd., Type F (SST).................................................3

0A-108187

Strainer Basket Assy..................................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 27 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands