STERO SD3 Series Service And Parts Manual Download Page 66

Page: 66 / 71

DRAIN WATER TEMPERING

(OPTIONAL ACCESSORY)

ILLUS.
PL-60524

PART NO.

NAME OF PART

AMT.

0P-638193

Strainer - Line (1/2) (Brass) (Incls. Items 2, 3, & 4)....................................................................1

0A-108194

Plug - Branch..............................................................................................................................1

0P-638194

Screen - Strainer (1/2 In.)...........................................................................................................1

0P-578195

Gasket........................................................................................................................................1

0P-688135

Pipe 1/2 x 1-1/8 TBE (Brass)......................................................................................................4

0P-548270

Valve - Solenoid (1/2) (120 V.)...................................................................................................1

0P-548093

Solenoid Valve (1/2) (120 V.) (Incls. Item 8)..............................................................................1

0P-548085

Coil - Solenoid Valve (120 V.)....................................................................................................1

0P-548094

Service Kit - 1/2 Solenoid Valve.................................................................................................1

0P-628093

Backflow Preventer....................................................................................................................1

0P-688319

Union - Pipe (Brass)...................................................................................................................1

0P-688321

Adapter 1-1/2 Brass to 1/2 FPT..................................................................................................1

0P-688328

Tee 1-1/2 x 1-1/2 x 1-1/2 (CPVC)...............................................................................................1

0P-688265

Adapter - Male 1-1/2 (CPVC).....................................................................................................1

0P-688272

Pipe 1-1/2 x 2-1/2 (CPVC)..........................................................................................................1

0P-688330

Elbow 1-1/2 x 90 Deg. (CPVC)...................................................................................................1

0P-688331

Y-Fitting 1-1/2 (CPVC)...............................................................................................................1

0P-688271

Pipe 1-1/2 x 6 (CPVC)................................................................................................................1

0P-688329

Adapter 1-1/2 CPVC to 1 FPT....................................................................................................1

0P-688327

Bushing - Pipe 1 to 3/8...............................................................................................................1

0P-678160

Self-Tapping Screw 8-18 x 3/8 Phil. Bndg. Hd., Type B.............................................................2

0P-658204

Thermostat (120 Deg.)...............................................................................................................1

0P-458273

Cable Assy.................................................................................................................................1

0P-458274

Wire (Transformer to Thermostat)..............................................................................................1

0P-458180

Wire Tie...................................................................................................................................AR

SD3 DISHWASHER REPLACEMENT PARTS

- 29 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands