Fig. 24
A.
Verify the FILL LED on relay board is lit
when J12 terminals on control board are
shorted together.
Fig. 25
1)
If the solenoid does not energize, but
the FILL LED on relay board is lit,
check relay board J1-7 for 120VAC.
a.
If 120VAC is not present across
J1-7 and X2, the relay board has
malfunctioned.
b.
If 120VAC is present across J1-7
and X2, remove the short from
J12 and check Fill/Rinse circuit.
NOTE:
When 1SOL is energized, the voltage across
J6-5 and ground will be zero or a few millivolts. Circuit
activation can be verified by measuring 5VDC voltage
across the control board +5VDC test pad and J6-5
when the FILL/RINSE circuit is active.
2)
If 1SOL does not energize and the FILL
LED does not light, check control board
voltage output to relay board across
J6-5 (control board) and ground =
0VDC (J6-5 and +5VDC test pad =
5VDC).
a.
If voltage measurements indicate
circuit is active, verify wiring to
relay board is correct. If correct,
replace relay board.
b.
If voltage measurements are not
present, replace control board.
c.
If voltage measurements remain
constant at approximately
4.5VDC, check the door interlock
circuit 1LS.
3)
If the 1SOL energizes, remove J12
short and replace the control board.
Long Fill Time (6 minutes)
1.
Verify the following.
A.
OPERATING CONDITIONS are satisfied as
stated at the beginning of this section.
B.
Control board is programmed to operate as
an SD3.
C.
Chamber door is closed.
D.
Flowing water pressure is correct (20psi ±
5psi).
E.
Float switch circuit test good and is
connected to wiring harness.
F.
Drain is closed and not leaking.
2.
If Low Water Level LED on control board is not lit
when float switch is operated (closed),
disconnect the thermistor and float connector
from J2 on control board.
Fig. 26
A.
Check continuity of float switch. Cycle float
(open and close) while observing meter.
B.
If continuity is not measured when float is
operated, check float switch circuit.
C.
If continuity exists, float is working normally.
SD3 Series - TROUBLESHOOTING
F45576 (1015)
Page 30 of 37
Summary of Contents for SD3 Series
