STERO SD3 Series Service And Parts Manual Download

Page: 56 / 71

RINSE PIPING

(WITH BOOSTER)

ILLUS.
PL-60519

PART NO.

NAME OF PART

AMT.

0P-678165

Lockwasher 5/16 Helical (SST)..................................................................................................2

0P-678142

Stop Nut 5/16-18 Hex (SST)......................................................................................................2

0B-108236

Piping - Fill..................................................................................................................................1

0P-628041

Vacuum Breaker (1/2 In.)...........................................................................................................1

0P-628042

Repair Kit - Vacuum Breaker......................................................................................................1

0P-658206

Probe Assy. - Rinse....................................................................................................................1

0P-658268

Gauge - Water Pressure Gauge - Water Pressure....................................................................1

0B-108238

Fill Piping Assy...........................................................................................................................1

0P-688317

Elbow - Pipe 1/2 x 90 Deg. (Brass)............................................................................................1

0P-688258

Hose - Water (Braided) (84 In.) (SST)........................................................................................1

0P-678139

Nut 5/16-18 Hex (SST)...............................................................................................................2

0P-678165

Lockwasher 5/16 Helical (SST)..................................................................................................2

0P-528129

Connector - Strain Relief............................................................................................................1

0A-108235

Bracket - Fill Piping....................................................................................................................1

0A-108228

Inside Rinse Piping Assy. Inside Rinse Piping Assy..................................................................1

0P-578172

O-Ring........................................................................................................................................1

0P-678150

0P-678150..................................................................................................................................2

0P-578196

Gasket - Rinse Pipe...................................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 19 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands