STERO SD3 Series Service And Parts Manual Download Page 52

Page: 52 / 71

LOWER WASH ARM

ILLUS.
PL-AI3998

PART NO.

NAME OF PART

AMT.

0P-678343

Set Screw 10-24 x 1/4 Hex Hdls., Cup Pt. (SST).......................................................................2

0A-108245

Arm - Rinse (Incls. Items 3 & 4).................................................................................................1

0A-108246

Plug - Rinse Arm........................................................................................................................2

0P-668243

Bearing.......................................................................................................................................1

0P-578178

O-Ring........................................................................................................................................1

0P-678338

Retaining Ring............................................................................................................................1

0A-108222

Wash Arm Assy. Wash Arm Assy. (Incls. Items 8, 9, & 10).......................................................1

0A-108221

Arm - Wash................................................................................................................................1

0P-678344

Mach. Screw 10-24 x 1/2 Phil. Truss Hd. (SST).........................................................................2

0B-108298

Hub - Wash Arm.........................................................................................................................1

0A-108234

Shaft - Rinse Arm Shaft - Rinse Arm..........................................................................................1

0B-108226

Manifold - Wash (Lower)............................................................................................................1

0P-578176

O-Ring........................................................................................................................................1

0P-578179

O-Ring........................................................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 15 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands