STERO SD3 Series Service And Parts Manual Download Page 60

Page: 60 / 71

ELECTRIC BOOSTER TANK

ILLUS.
PL-60521

PART NO.

NAME OF PART

AMT.

0P-678142

Stop Nut 5/16-18 Hex (SST)......................................................................................................1

0P-678169

Washer (SST).............................................................................................................................1

0P-678340

Cap Screw 5/16-18 x 3/4 Hex Hd. (SST)...................................................................................1

0A-108281

Bracket - Booster Support..........................................................................................................1

0P-558276

Heater (240 V., 8.5 kW)..............................................................................................................1

0P-558275

Heater (208V., 8.5 kW)...............................................................................................................1

0P-558277

Heater (480 V., 8.5 kW)..............................................................................................................1

0P-678332

Nut 1/4-20 Hex (Brass)...............................................................................................................6

0A-108282

Bracket - Booster Mounting........................................................................................................1

0B-108269

Tank - Booster Weldment...........................................................................................................1

0P-688317

Elbow - Pipe 1/2 x 90 Deg. (Brass)............................................................................................1

0A-108280

Bracket - High Limit....................................................................................................................1

0P-658205

Protector - High Limit Protector - High Limit...............................................................................2

0P-658206

Probe Assy. - Rinse....................................................................................................................1

0P-578215

Gasket (13 kW) (Electric Heater)...............................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 23 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands