STERO SD3 Series Service And Parts Manual Download Page 70

Page: 70 / 71

PANELS AND RACK SUPPORT

ILLUS.
PL-AI3996

PART NO.

NAME OF PART

AMT.

0P-678149

Cap Screw 5/16-18 x 5/8 Hex Hd. (SST)...................................................................................5

0A-108264

Rack - Stop Assy........................................................................................................................1

0P-678142

Stop Nut 5/16-18 Hex (SST)......................................................................................................5

0P-578173

O-Ring........................................................................................................................................1

0P-678138

Nut 1/4-20 Hex (SST).................................................................................................................1

0P-678164

Lockwasher 1/4 Helical (SST)....................................................................................................1

0A-108191

Retainer - Cap............................................................................................................................1

0B-108190

Cap & Stud Assy........................................................................................................................1

0P-458263

Wireform Assy............................................................................................................................1

0P-678342

Cap Screw 1/4-20 x 1/2 Hex Hd. (SST).....................................................................................2

0P-678164

Lockwasher 1/4 Helical (SST)....................................................................................................2

0A-108230

Panel - Cover (Right Side).........................................................................................................1

0P-578266

Kit - Foam Installation..............................................................................................................AR

0A-108252

Foot - Flanged (With Holes).......................................................................................................4

0A-108253

Foot - Standard..........................................................................................................................4

0P-678345

Mach. Screw 1/4-20 x 1/2 Phil. Truss Hd...................................................................................2

0P-678164

Lockwasher 1/4 Helical (SST)....................................................................................................2

0A-108229

Panel - Cover (Front)..................................................................................................................1

0P-578212

Foam Tape..............................................................................................................................AR

0P-578224

Seal - Extrusion.......................................................................................................................AR

0P-578212

Foam Tape..............................................................................................................................AR

0P-678164

Lockwasher 1/4 Helical (SST)....................................................................................................2

0P-678342

Cap Screw 1/4-20 x 1/2 Hex Hd. (SST).....................................................................................2

0A-108223

Panel - Cover (Left Side)............................................................................................................1

0A-108579

Deflector, Splash Out, Tank.......................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 33 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands