STERO SD3 Series Service And Parts Manual Download

Page: 58 / 71

BOOSTER PIPING

ILLUS.
PL-60520

PART NO.

NAME OF PART

AMT.

0P-688325

Pipe 1/2 x 7 TBE (Brass)............................................................................................................1

0P-688317

Elbow - Pipe 1/2 x 90 Deg. (Brass)............................................................................................1

0P-688318

Tee - Pipe 1/2 x 1/2 x 1/2 (Brass)...............................................................................................1

0P-688322

Pipe Plug 1/2 Sq. Hd. (Brass)....................................................................................................1

0P-688323

Pipe 1/2 x 1-1/4 TBE (Brass)......................................................................................................1

0P-548093

Solenoid Valve (1/2) (120 V.).....................................................................................................1

0P-548094

Service Kit - 1/2 Solenoid Valve..............................................................................................AR

0P-548085

Coil - Solenoid Valve (120 V.)....................................................................................................1

0P-688323

Pipe 1/2 x 1-1/4 TBE (Brass)......................................................................................................1

0P-688317

Elbow - Pipe 1/2 x 90 Deg. (Brass)............................................................................................1

0P-688319

Union - Pipe (Brass)...................................................................................................................1

0P-688317

Elbow - Pipe 1/2 x 90 Deg. (Brass)............................................................................................1

0P-688323

Pipe 1/2 x 1-1/4 TBE (Brass)......................................................................................................1

0P-688320

Bushing - Pipe 3/4 to 1/2 (Brass)...............................................................................................1

0P-638036

Strainer - Line (3/4 In.) (Brass) (Incls. Items 16, 17, & 18).........................................................1

0P-688037

Plug - Branch..............................................................................................................................1

0P-688039

Screen - Line Strainer................................................................................................................1

0P-578038

0P-578038..................................................................................................................................1

SD3 DISHWASHER REPLACEMENT PARTS

- 21 -

F-43302 Rev. B (October 2015)

Summary of Contents for SD3 Series








































































Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands

STERO SD3 Series, Service And Parts Manual

Search results

Summary of Contents for SD3 Series

Reviews:

Related manuals for SD3 Series

Brands by name

Popular brands