Star Micronics IFBD-BE07 User Manual Download Page 61 | Manualshive

Page: 61 / 89

background image

IFBD-HE0708 BE07 User’s Manual

6-2

6.2 Printer Firmware Support Table

Can be used with the F/W versions shown in the table below. (As of August 16, 2017)

Model

Supports IFBD-HE07/08/BE07

Supports

IFBD-HE07X/08X/BE07X

Supports Broken Link Detection

(LED Blinking Operation,

Warnign Print Operation)

Boot

Main

Boot

Main

TSP800II

Ver1.0

Ver1.2

×

×

○

FVP10

Ver1.0

Ver1.3

Ver1.0(Note1)

Ver1.3(Note1)

Ver1.5(Note2)

○

SP500(Note3)

Ver4.0

Ver4.0

×

×

×

SP700

Ver2.0

Ver3.0

×

Ver3.3(Note2)

○

TSP700II

Ver2.0

Ver3.0

Ver2.0(Note1)

Ver3.0(Note1)

Ver4.1(Note2)

○

TSP650(Note3)

Ver2.0

Ver3.0

×

×

○

TSP650II

Ver1.0

Ver1.0

Ver1.0(Note1)

Ver1.0(Note1)

Ver1.2(Note2)

○

TUP500(Note3)

Ver2.0

Ver3.0

×

×

○

TSP1000(Note3)

Ver4.0

Ver3.0

×

×

×

TSP828L(Note3)

Ver2.0

Ver2.0

×

×

×

HSP7000(Note3)

Ver2.1

Ver5.0

×

×

○

TCP300II(Note3)

-

Ver3.0

×

×

×

TCP400(Note3)

-

Ver3.0

×

×

×

○: Supported; ×: Not supported

Note 1:   Only European and U.S. models
Note 2:   European and U.S. models(As UTF-8 is not supported), kanji models (As UTF-8 is supported)
Note 3:   Models indicated by (*3) are not supported by this product with F/W Ver. 5.0.0 and later. Use the product with F/W Ver. 4.X.X or earlier.

«
...
59
60
61
62
63
...
»

Summary of Contents for IFBD-BE07


























































































Reviews:

No comments

Related manuals for IFBD-BE07

Brand: Paradyne Pages: 22

Pixie-4 Express

Brand: XIA Pages: 17

Brand: Cypress Semiconductor Pages: 10

Brand: Rane Pages: 6

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

Brand: Paradyne Pages: 10

Brand: Billion Pages: 8

Brand: StarTech.com Pages: 2

EPON SFU Series

Brand: Zte Pages: 26

Brand: ANTUMBRA Pages: 11

Brand: Frontier Pages: 8

Brand: EMC Pages: 51

Brand: Cooltek Pages: 2

Brand: Corsham Technologies Pages: 15

NexXxoS GPX GPX-A 280-M11

Brand: Alphacool Pages: 4

Brand: Alphacool Pages: 4

Brand: Alphacool Pages: 4

Alphacool Eisbecher Aurora D5

Brand: Alphacool Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands