background image

IFBD-HE0708 BE07 User’s Manual

6-3

6.3  Driver Support Table

Drivers support table for IFBD-HE07/08/BE07. (As of August 16, 2017)

6.3.1.  Small Model Printers

6.3.1.1. Star PRNT Inteligence CD (Multi-model support CD)

StarPRNT Inteligence Ver1.1  (Note 2)

Model

Printer Driver

OPOS Ver1.13.2 or later

StarIO Ver1.2.2 or later

TSP800II

○ (Note 1)

FVP10

○ (Note 1)

TSP700II

TSP650 (Note 5)(Note6)

SP500(Note6)

SP700

TUP500 (Note 3)(Note6)

TSP650II (Note 4)

Note1

 With Star PRNT Inteligence CD, supports IFBD-HE07/08/BE07 from Ver. 1.1.

Note2:  You can search for printers that do not have an IP address in environments that do not pass through a DHCP server, using a combination of IFBD-HE07/HE08/BE07 

Ver. 2.2.0 or later and StarPRNT Intelligence Ver2.0 or later. For earlier versions, you cannot search for printers that do not have an IP address in environments 

that do not pass through a DHCP server. Select “Help - Cannot find printer”, and then follow the steps to setup a temporary IP address. 

Note3:  StarPRNT Intelligence Ver. 1.4 or later supports TUP500. 
Note4:  StarPRNT Intelligence Ver. 2.0 or later supports TUP650II. 
Note5:  StarPRNT Intelligence Ver. 2.0 or later does not support TSP650. Use StarPRNT Intelligence Ver. 1.5 with TSP650.
Note6:  The models indicated with *6 are not supported by this product with F/W Ver.5.0.0 or later. Use the product with F/W Ver. 4.X.X or earlier.

Summary of Contents for IFBD-BE07


























































































Reviews: