Star Micronics IFBD-BE07 User Manual Download Page 41

Page: 41 / 89

IFBD-HE0708 BE07 User’s Manual

3-32

Name

Description

ipRouteDest

Destination IP address of this route (0.0.0.0 = Default route)

ipRouteIfIndex

Interface identification number for transmitting to the next destination host on this

route (= ifIndex)

IpRouteMetric

Primary routing metric for this route (-1 = Not used)

ipRouteNextHop

IP address of next hop on this route

IpRouteType

Route types (1: None of the following, 2: Invalid route, 3: Direct connection, 4:

Indirect connection)

IpRouteProto

Routing mechanism by which this route was learned

IpRouteAge

Elapsed time after this route was last confirmed as a normal route [sec]

IpRouteMask

Value which performs logical AND before comparison with ipRouteDest or the

destination address

ipRouteInfo

MIB definition number for routing protocol used for this route

ipNetToMediaIfIndex

Interface identification number for this entry (=ifIndex)

ipNetToMediaPhysAddress

Media-dependent physical address

ipNetToMediaNetAddress

IP address corresponding to the physical address of this entry

ipNetToMediaType

Address conversion method (1: None of the following, 2: Invalid value, 3: Dynamic

conversion, 4: Static conversion)

icmpInMsgs

Total number of received ICMP

icmpInErrors

Number of received ICMP messages that were discarded due to checksum error

or other ICMP specification error

icmpInDestUnreachs

Number of ICMP destination-unreachable messages received

icmpInTimeExcds

Number of ICMP time-exceeded messages received

icmpInParmProbs

Number of ICMP parameter-problem messages received

icmpInSrcQuenchs

Number of ICMP source-quench messages received

icmpInRedirects

Number of ICMP redirect messages received

icmpInEchos

Number of ICMP echo-request messages received

icmpInEchoReps

Number of ICMP echo-reply messages received

icmpInTimestamps

Number of ICMP timestamp-request messages received

icmpInTimestampReps

Number of ICMP timestamp-reply messages received

icmpInAddrMasks

Number of ICMP address mask request messages received

icmpInAddrMaskReps

Number of ICMP address mask reply messages received

icmpOutMsgs

Total number of ICMP messages transmitted

icmpOutErrors

Number of ICMP messages that were discarded and not transmitted due to full

buffer or other reason at time of ICMP transmission

icmpOutDestUnreachs

Number of ICMP destination-unreachable messages transmitted

icmpOutTimeExcds

Number of ICMP time-exceeded messages transmitted

icmpOutParmProbs

Number of ICMP parameter-problem messages transmitted

icmpOutSrcQuenchs

Number of ICMP source-quench messages transmitted

icmpOutRedirects

Number of ICMP redirect messages transmitted

icmpOutEchos

Number of ICMP echo-request messages transmitted

icmpOutEchoReps

Number of ICMP echo-reply messages transmitted

icmpOutTimestamps

Number of ICMP timestamp-request messages transmitted

icmpOutTimestampReps

Number of ICMP timestamp-reply messages transmitted

icmpOutAddrMasks

Number of ICMP address mask request messages transmitted

icmpOutAddrMaskReps

Number of ICMP address mask reply messages transmitted

Summary of Contents for IFBD-BE07


























































































Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands

Star Micronics IFBD-BE07, User Manual

Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands