Star Micronics IFBD-BE07 User Manual Download Page 88

Page: 88 / 89

IFBD-HE0708 BE07 User’s Manual

7-22

7.1.4. Required Settings when Registering Certificates with iOS 10.3 or Later

With iOS 10.3 or later, when a certificate was installed manually, that certificate is not automatically trusted for SSL communication.

Settings at the iOS device are needed. An example of the iOS settings is shown below for reference.

(For details, check the Apple HP. https://support.apple.com/ja-jp/HT204477)

1. Follow the procedure in “3. Import a certificate to the web browser” in section “7.1.1. Using a self-signed certificate” and import

the certificate.

2. In sequence, select “Settings” > “General” > “About” > “Certificate Trust Settings”.

3. Enable certificate trust with “ENABLE FULL TRUST FOR ROOT CERTIFICATES”.

Use the address beginning with “https://” and check that the printer web setting screen is displayed correctly.

Summary of Contents for IFBD-BE07


























































































Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands

Star Micronics IFBD-BE07, User Manual

Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands