Star Micronics IFBD-BE07 User Manual Download Page 11

Page: 11 / 89

IFBD-HE0708 BE07 User’s Manual

3-2

3.1.1 IP Address Setting

This product has a static (fixed condition) and dynamic (DHCP/BOOTP, RARP, and ARP/Ping) IP address. It is possible to specify a

sub-net mask and default gateway with static and DHCP, BOOTP.

In the default settings, static is invalid and dynamic is valid.

The following pages describe how to acquire an IP address for each. See section 3.1.1.5 Address Acquisition Process Transition for

details on each protocol transition state.

This product allows you to check the current IP parameter information while operating by a self-print when turning the power on.

This is output in the following format after running a self-print. See section 3.2.3 Self-print for details on running a self print.

* Protocol: The IP address acquisition protocol below is shown in the parentheses of the operating IP address line.

(Static):

Static (Fixed address)

(DHCP):

Gets from DHCP server

(BOOTP):

Gets from BOOTP server

(RARP):

Gets from RARP server

(Didn’t obtain):

No IP address was acquired.

You can find the MAC address to use in this section by using one of the following methods.

1. Execute a printer self-print (see section 3.2.5).

2. Check the first 12 characters in the barcode label affixed to the I/F card connector.

Example for when the MAC address is 00:11:62:11:11:11

Summary of Contents for IFBD-BE07


























































































Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands

Star Micronics IFBD-BE07, User Manual

Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands