Star Micronics IFBD-BE07 User Manual Download Page 7

Page: 7 / 89

IFBD-HE0708 BE07 User’s Manual

2-2

2.2 Specifications

Network I/F Unit:

IEEE802.3/3u

(10BASE-T Ethernet / 100BASE-TX Fast Ethernet)

LED:

Red x 1; Green x 1

Red: LINK/Activity

Green: 100BASE-TX

*Displays with flashing patterns when executing a special mode.

Switch for Settings:

Push Switch x 1

DIP SW (dipole) x 1

See sections 3.2.2 Push Switches and 3.2.3 DIP Switches for details on

each specification.

PCB Dimensions:

69 mm x 61 mm (Tolerance ± 0.5 mm)

t = 1.6 mm (Tolerance ± 0.2 mm)

Product Weight:

IFBD-HE07:

Approximately 63 g

IFBD-HE08:

Approximately 65 g

IFBD-BE07:

Approximately 118 g

The weights above do not include packing materials or accessories.

Power Supply:

Operating Voltage 5V ±5%

Rated Current Consumption 500 mA Max.

Summary of Contents for IFBD-BE07


























































































Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands

Star Micronics IFBD-BE07, User Manual

Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands