Star Micronics IFBD-BE07 User Manual Download Page 4

Page: 4 / 89

IFBD-HE0708 BE07 User’s Manual

1-1

1. GENERAL DESCRIPTION

This is an embedded network interface card (printer server) for STAR POS printers.*

* In this document, this product is called NIC (an acronym for network interface card).

1.1 Features



Supports Star Micronics POS printers (including card readers and writers).

See section 2.1 Model Names for details on supported printers.

This product receives electric power from the printer, so there is no need to prepare a

separate AC adapter.



The physical layer conforms to IEEE802.3/3u (10BASE-T/100BASE-TX).



Ethernet communication settings (10BASE-T/100BASE-TX, Full/Half Duplex) with the

connected device are doen using Auto Negotiation.



This can be used in a LAN (Local Area Network) environment.



Communication protocols support TCP/IP (IPv4).



Prints using LPR, Raw Socket Print (TCP #9100) and FTP protocols.



This receives status information (ready status, causes of errors, and the like) issued from the

printer and allows that information to be loaded onto a PC.



Can be used simultaneously from multiple protocols.

Raw Socket Print (#9100) also prints using multi-session.(*1)

(Note *1) The factory default setting for multi-session for Raw Socket Print (#9100) differs between the old

product IFBD-HE05/06/BE05 and this product IFBD-HE07/08/BE07.Be careful if you are switching from an old

product.

IFBD-HE05/06/BE05 (old product): Valid

IFBD-HE07/08/BE07 (this product): Invalid



The IP address for this product can be static or obtained by DHCP/BOOTP, RARP, ARP/Ping.



Flash ROM is mounted on the board. Firmware updates are possible via FTP over a network.



You can change this product and printer settings and monitor their states using device specific setting utilities,

HTTP (WEB), TELNET, and FTP.

Network settings that are set using HTTP (Web), Telnet, FTP for the IP address and #9100 multi-session are

stored in the product’s non-volatile memory.



To be prepared for the unlikely event that the main firmware malfunctions for some reason, the boot loader of

this product is provided a TFTP client function to allow you to download firmware from the server over the

network for recovery of your firmware.



Supports Star Micronics' Windows Printer Driver, OPOS Driver, JPOS Driver (Windows, Linux, and Mac),

CUPS Driver (Linux, Mac)



Supports the proprietary StarWebPRNT function from STAR MICRONICS CO., LTD. that allows direct printing

from Web applications that support HTML 5. (IFBD-HE07X/08X/BE07X only)

1.2 Differences between IFBD-HE07/08/BE07 and IFBD-07X/08X/BE07X

IFBD-HE07/08/BE07 and IFBD-07X/08X/BE07X are different products. Some of these products support StarWeb-

PRNT and some do not.

IFBD-HE07/08/BE07: StarWebPRNT not supported

IFBD-HE07X/08X/BE07X: StarWebPRNT supported

IFBD-HE07X/08X/BE07X is upwardly compatible with IFBD-HE07/08/BE07, and except for sections involving the

StarWebPRNT function the specifications for IFBD-HE07/08/BE07 are covered by the specifications for IFBD-

HE07X/08X/BE07X.

See “4. StarWebPRNT Function” for more details.

Summary of Contents for IFBD-BE07


























































































Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands

Star Micronics IFBD-BE07, User Manual

Search results

Summary of Contents for IFBD-BE07

Reviews:

Related manuals for IFBD-BE07

Brands by name

Popular brands