manualshive.com logo in svg

ST STM32WL5 Series, Reference Manual, Page: 1272 / 1454

Share
Download
ST STM32WL5 Series Reference Manual Download Page 1272

Serial peripheral interface / integrated interchip sound (SPI/I2S)

RM0453

1272/1454

RM0453 Rev 2

RxFIFO threshold setting and the following read access must be always kept aligned at the 
receiver side, as data can be lost if it is not in line.

A specific problem appears if an odd number of such “fit into one byte” data frames must be 
handled. On the transmitter side, writing the last data frame of any odd sequence with an 8-
bit access to SPIx_DR is enough. The receiver has to change the Rx_FIFO threshold level 
for the last data frame received in the odd sequence of frames in order to generate the 
RXNE event.

Figure 355. Packing data in FIFO for transmission and reception

1. In this example: Data size DS[3:0] is 4-bit configured, CPOL=0, CPHA=1 and LSBFIRST =0. The Data 

storage is always right aligned while the valid bits are performed on the bus only, the content of LSB byte 

goes first on the bus, the unused bits are not taken into account on the transmitter side and padded by 

zeros at the receiver side.

Communication using DMA (direct memory addressing)

To operate at its maximum speed and to facilitate the data register read/write process 
required to avoid overrun, the SPI features a DMA capability, which implements a simple 
request/acknowledge protocol.

A DMA access is requested when the TXE or RXNE enable bit in the SPIx_CR2 register is 
set. Separate requests must be issued to the Tx and Rx buffers.

•

In transmission, a DMA request is issued each time TXE is set to 1. The DMA then 
writes to the SPIx_DR register.

•

In reception, a DMA request is issued each time RXNE is set to 1. The DMA then reads 
the SPIx_DR register.

See 

Figure 356

 through 

Figure 359

.

When the SPI is used only to transmit data, it is possible to enable only the SPI Tx DMA 
channel. In this case, the OVR flag is set because the data received is not read. When the 
SPI is used only to receive data, it is possible to enable only the SPI Rx DMA channel.

In transmission mode, when the DMA has written all the data to be transmitted (the TCIF 
flag is set in the DMA_ISR register), the BSY flag can be monitored to ensure that the SPI 
communication is complete. This is required to avoid corrupting the last transmission before 
disabling the SPI or entering the Stop mode. The software must first wait until 
FTLVL[1:0]=00 and then until BSY=0. 

0x04 0x0A

SPI fsm 

& shift

TXFIFO

SPIx_DR

0x0A

0x04

0x0A

0x04

SPI fsm 

& shift

0x0A

0x04

0x04 0x0A

SPIx_DR

16-bit access when write to data register

16-bit access when read from data register

NSS

SCK

MOSI

RXFIFO

MS19590V1

SPI_DR= 0x040A when TxE=1

SPI_DR= 0x040A when RxNE=1

Summary of Contents for STM32WL5 Series















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments