Spokey 920866, User Manual

Page: 9 / 60

8
LIST OF PARTS - DIAGRAM
– P. 51
No. Description Qty No. Description Qty No. Description Qty
1 counter 1 38 lower handlebar post cover 1 75 left pedal crank 1
2 bolt M5*10L 4 39 main frame 1 76 left crank cover 1
3 handlebar post 1 40 sensor holder 1 77 left cover 1
4 front handlebar post cover 1 41 bolt M5*10L 2 78 rear stabilizer left end cap 1
5 bolt ST2.9*30L 4 42 knob M16 1 79 rear stabilizer 1
6 bolt M5*10L 2 43 seat post sleeve 1 80 rear stabilizer right end cap 1
7
foam handlebar cover
φ20*5T*590L
2 44
drive wheel Ф260
1 81 adjustment wheel 2
8
handlebar φ22.2*2T*1310L
1 45 drive belt 440J6 1 82 stabilizer foot 2
9 end cap 2 46 crank
axle Ф17*176
1 83 nut M8 1
10 bolt ST3.9*20L 2 47 bolt M6*16L 4 84
sleeve Ф10*Ф14*3mm
1
11 pulse sensor wire 2 48
spring washer Ф6.1*1.6T
4 85 bearing 6000 1
12 pulse sensor 2 48 nut M6*5.5T 4 86 pulley 1
13 flat washer
Ф8*Ф19*2T
1 50 C-clip
Ф15.7*Ф19.4*1T
2 87 nut M8 1
14 spring washer
Ф8.5*Ф13.5*2.5T
1 51
wave washer Ф17.5*Ф25*0.3T
1 88 flat washer
Ф8*Ф19*2T
1
15
resistance adjustment wire (from
the counter)
1 52 flat washer
Ф17.5*Ф25*0.3T
1 89
spring 0Dφ16*φ2*45n
1
16 rear handlebar post cover 1 53 bearing 6203 2 90 tensioner lever 1
17 knob M8 1 54 resistance engine 1 91 bolt M8*20L 1
18 seat 1 55 bolt M5*12 1 92 flat washer
Ф8*Ф19*2T
1
19 seat base 1 56
flat washer Ф5.5*Ф12.5
1 93 bearing 6000 1
20 sleeve 2 57 bolt ST3.9 4 94
nut 3/8”-26*7T
2
21 end cap 1 58 nut M8 1 95
bolt 3/8”-26*3.8T
3
22 bolt M6*12L 1 59 bolt M8*55L 1 96
sleeve Ф10*Ф14*3mm
1
23 knob M16 1 60 flat washer
Ф8*Ф19*2T
1 97
flywheel axle Ф11.5*130L
1
24 seat post 1 61 magnets 1 98 power supply 1
25 front stabilizer 1 62 resistance control fastening 1 99 bearing 6300 1
26 front stabilizer left end cap 1 63 spring 1 100 flat washer
Ф30*Ф34*0.8T
1
27 front stabilizer right end cap 1 64 Allen wrench 1 101 bearing 6003 2
28 transport roll 2 65 plastic insert 2 102
bearing Ф35*17
1
29
axle φ7.9*34.4
2 66 bolt ST3.9*50L 7 103
flywheel Ф280*32W*8KG
1
30 front stabilizer base 1 67 right cover 1 104
small pulley Ф34*8J
1
31 flat washer
φ10.5*φ38*3T
2 68
bolt 3/16”*3/4”
6 105 bearing 6000 1
32 bolt 3/16"*20L 2 69 bolt ST2.9*8L 8 106 resistance adjustment wire 1
33 flat washer
Ф8*Ф19*2T
4 70 left crank cover 1 107
resistance adjustment wire
(from the frame) 1
34 bolt M8*75L 4 71 right pedal
crank 9/16”
1 108 power cord 1
35 bolt M8*16L 4 72 bolt M8*20L 2 109
sleeve Ф10*Ф14*11mm
1
36 spring washer
Ф8.5*Ф13.5*2.5T
4 73
right pedal 9/16”
1 110 wrench 13
,
14
1
37
curved washer Ф8*Ф19*2T
4 74
left pedal 9/16”
1 111 wrench 13
,
14
,
15
1
PREPARATIONS
1. Before assembly make sure there is enough space.
2. Use the recommended tools.
3. Before assembly check if there are all the parts in the box.
It is recommended that product should be assembled by at least two people
to avoid injuries. Most of the assembly equipment listed here has been packed separately,
but some elements come preassembled in certain assembly parts. If it is
required, dissassemble them and assemble again.
Read the instructions of all assembly steps and familiarize with all the
devices installed.
ASSEMBLY INSTRUCTIONS ( Drawings
– p.
53-56)
Note: Follow the assembly instructions below:
STEP 1 Fix the front (25) and the rear stabilizer (79) with flat washers
Ф8*Ф19*2T (33) and bolts M8*75L (34).
STEP 2 Mount the handlebar.
1. Before screwing it, remember to pull through the pulse sensor wires
through the handlebar post.
2. To fix the handlebar (8), place the plastic cover (16) on it and secure it
with the washers (13, 14) and knob (17).
ASSEMBLY, SETUP AND MAINTENANCE