Speedtouch SpeedTouch 716v5 (WL) Cli Reference Manual Download Page 409

Page: 409 / 796

IP Commands

E-DOC-CTC-20060414-0006 v1.0

387

IP Commands

Introduction

This chapter describes the commands of the

command group.

Contents

This chapter covers the following commands:

ip arpadd

Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface.

389

ip arpdelete

Delete an entry from the ARP cache.

390

ip arplist

Display the ARP cache.

391

ip config

Show/set global IP stack configuration options.

392

ip flush

Flush all the static IP parameters.

394

ip ifadd

Create an IP interface.

395

ip ifattach

Attach an IP interface.

396

ip ifconfig

Configure the parameters of an IP interface.

397

ip ifdelete

Delete an IP interface.

399

ip ifdetach

Detach an IP interface.

400

ip iflist

Display all the IP interfaces.

401

ip ifwait

Wait for a status change of an IP interface.

402

ip ipadd

Assign an IP address to an IP interface.

403

ip ipconfig

Modify an IP address configuration.

404

ip ipdelete

Remove an IP address from an IP interface.

405

ip iplist

Display all the configured IP addresses.

406

ip mcast rtadd

Add a multicast route to the multicast routing table.

407

ip mcast rtdelete

Delete a multicast route from the multicast routing table.

408

ip mcast rtlist

Display the multicast routing table.

409

ip mcast flush

Flush the multicast routing table.

410

ip rtadd

Add a route to the routing table.

411

ip rtdelete

Delete a route from the routing table.

412

ip rtlist

Display the routing table.

413

ip auto flush

Flush the autoIP interfaces.

414

ip auto ifadd

Create an autoIP interface.

415

ip auto ifattach

Select and assign a link-local address to an autoIP interface.

416

ip auto ifconfig

Configure an autoIP interface.

417

ip auto ifdelete

Delete an existing autoIP interface.

419

ip auto ifdetach

Release the link-local address for the given autoIP interface.

420

ip auto iflist

Display the autoIP interfaces.

421

ip debug httpprobe

Send a HTTP probe.

422

Summary of Contents for SpeedTouch 716v5 (WL)




























































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SpeedTouch 716v5 (WL)

Reviews:

Related manuals for SpeedTouch 716v5 (WL)

Brands by name

Popular brands

Speedtouch SpeedTouch 716v5 (WL), Cli Reference Manual

Search results

Summary of Contents for SpeedTouch 716v5 (WL)

Reviews:

Related manuals for SpeedTouch 716v5 (WL)

Brands by name

Popular brands