SpectraLink 8440 Administration Manual Download Page 314

Page: 314 / 335

Spectralink 84-Series Series Wireless Telephones Administration Guide

1725-86984-000_P.docx
September 2016

314

Response

Supported

486 Busy Here

Yes

487 Request Terminated

Yes

488 Not Acceptable Here

Yes

491 Request Pending

493 Undecipherable

5xx Responses - Server Failure

Supported 5xx SIP Responses

Response

Supported

5-Server Internal Error

Yes

501 Not Implemented

Yes

502 Bad Gateway

503 Service Unavailable

504 Server Time-out

505 Version Not Supported

513 Message Too Large

6xx Responses - Global Failure

Supported 6xx SIP Responses

Response

Supported

600 Busy Everywhere

603 Decline

Yes

604 Does Not Exist Anywhere

606 Not Acceptable

Hold Implementation

The handset supports two currently accepted means of signaling hold.

The first method, no longer recommended due in part to the RTCP problems associated with it,
is to set

the “c” destination addresses for the media streams in the SDP to zero, for example,

c=0.0.0.0.

Summary of Contents for 8440
















































































































































































































































































































































Search results

Summary of Contents for 8440

Reviews:

Brands by name

Popular brands

SpectraLink 8440, Administration Manual

Search results

Summary of Contents for 8440

Reviews:

Brands by name

Popular brands