Home
/
SpectraLink
/
8440
/
Administration Manual

SpectraLink 8440, Administration Manual

Share

Page: 107 / 335

SpectraLink 8440 Administration Manual Download Page 107

Spectralink 84-Series Series Wireless Telephones Administration Guide

1725-86984-000_P.docx
September 2016

107

Summary

Parameter

Used to:

tone.dtmf.chassis.masking

Specify if DTMF tones should be played through the speakerphone

tone.dtmf.level

Specify the frequency level of DTMF digits

tone.dtmf.offTime

Specify how long the handset should wait between DTMF digits

tone.dtmf.onTime

Specify how long the handset should play each DTMF tone for

tone.dtmf.viaRtp

Enable or disable DTMF encoding in an RTP stream

Table 8-21: DTMF Tone Parameters

Parameter

Permitted Values

Default

tone.dtmf.chassis.masking

1

0 or 1

0

If 0, DTMF tones will be played through the speakerphone in handsfree mode. If 1 (set only if

tone.dtmf.viaRtp

is set to 0), DTMF tones will be substituted with non-DTMF pacifier tones when dialing in

handsfree mode

– this is to prevent the tones from broadcasting to surrounding telephony devices or being

inadvertently transmitted in-band due to local acoustic echo.

tone.dtmf.level

1

-33 to 3

-15

The level of the high frequency component of the DTMF digit measured in dBm0; the low frequency tone will be
two dB lower.

tone.dtmf.offTime

1

positive integer

50

When a sequence of DTMF tones is played out automatically, this is the length of time in milliseconds the handset
will pause between digits. This is also the minimum inter-digit time when dialing manually.

tone.dtmf.onTime

1

positive integer

50

When a sequence of DTMF tones is played out automatically, this is the length of time in milliseconds the tones
will be played for. This is also the minimum time the tone will be played when dialing manually (even if key press is
shorter).

tone.dtmf.viaRtp

1

0 or 1

1

If set to 1, encode DTMF in the active RTP stream. Otherwise, DTMF may be encoded within the signaling
protocol only when the protocol offers the option.

Note

: If this parameter is set to 0,

tone.dtmf.chassis.masking

should be set to 1.

1

Change causes handset to restart or reboot.

DTMF Event RTP Payload

The handset is compatible with

RFC 2833

—RTP Payload for DTMF Digits, Telephony Tones,

and Telephony Signals

. RFC 2833 describes a standard RTP-compatible technique for

conveying DTMF dialing and other telephony events over an RTP media stream. The handset
generates RFC 2833 (DTMF only) events but does not regenerate

– or otherwise use – DTMF

events received from the remote end of the call. Use the next table to set up this feature.

«
...
105
106
107
108
109
...
»

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands