manualshive.com logo in svg

SpectraLink 8440, Administration Manual

Share
Download
SpectraLink 8440 Administration Manual Download Page 175

Spectralink 84-Series Series Wireless Telephones Administration Guide 

1725-86984-000_P.docx 
September 2016 

175 

Parameter 

Permitted Values 

Default 

voIpProt.SDP.useLegacyPayloadTypeNegotiation

 

0 or 1

 

0

 

If set to 1, the handset transmits and receives RTP using the payload type identified by the first codec listed in the 
SDP of the codec negotiation answer. 
If set to 0, RFC 3264 is followed for transmit and receive RTP payload type values. 

Table 8-56: Session Initiation Protocol (SIP) Parameters 

Parameter 

Permitted Values 

Default 

voIpProt.SIP.acd.signalingMethod

1

 

0 or 1 

0 

If set to 0, th

e ‘SIP-B’ signaling is supported. (This is the older ACD functionality.) 

If set to 1, the feature synchronization signaling is supported. (This is the new ACD functionality.) 

voIpProt.SIP.CID.sourcePreference 

ASCII string up to 
120 characters 
long 

Null 

Specify the priority order for the sources of caller ID information. The headers can be in any order. 
If Null, caller ID information comes from 

P-Asserted-Identity

, 

Remote-Party-ID

, and 

From

 in that order. 

The values 

From,P-Asserted-Identity, Remote-Party-ID

 and 

P-Asserted-Identity, Remote-

Party-ID

 are also valid. 

voIpProt.SIP.compliance.RFC3261.validate.contentLanguage 

0 or 1 

1 

If set to 1, validation of the SIP header content language is enabled. If set to 0, validation is disabled. 

voIpProt.SIP.compliance.RFC3261.validate.contentLength 

0 or 1 

1 

If set to 1, validation of the SIP header content length is enabled. If set to 0, validation is disabled. 

voIpProt.SIP.compliance.RFC3261.validate.uriScheme 

0 or 1 

1 

If set to 1, validation of the SIP header URI scheme is enabled. If set to 0, validation is disabled. 

voIpProt.SIP.conference.address 

ASCII string up to 
128 characters 
long 

Null 

If Null, conferences are set up on the handset locally. 
If set to some value, conferences are set up by the server using the conferencing agent specified by this address. 
Acceptable values depend on the conferencing server implementation policy. 

voIpProt.SIP.conference.parallelRefer 

0 or 1

 

0 

If 1, a parallel REFER is sent to the call server. 

Note:

 

This parameter must be set for Siemens Openscape 

Centralized Conferencing.

 

voIpProt.SIP.connectionReuse.useAlias 

0 or 1 

0 

If set to 0, this is the old behavior. 
If set to 1, handset uses the connection reuse draft which introduces "alias". 

voIpProt.SIP.csta 

0 or 1 

0 

If 0, the uaCSTA (User Agent Computer Supported Telecommunications Applications) feature is disabled. If 1, 
uaCSTA is enabled (If 

reg.x.csta

 

is set, it will overrule this parameter). 

voIpProt.SIP.dialog.strictXLineID 

0 or 1 

0 

If 0, the handset will not look for x-line-id (call appearance indec) in a SIP INVITE message, if one is not present. 
Instead, when it receives INVITE, the handset will generate the call appearance locally and pass that information to 
other parties involved in the call. 

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands