Home
/
SpectraLink
/
8440
/
Administration Manual

SpectraLink 8440, Administration Manual

Share

Page: 252 / 335

SpectraLink 8440 Administration Manual Download Page 252

Spectralink 84-Series Series Wireless Telephones Administration Guide

1725-86984-000_P.docx
September 2016

252

Shared Call Appearance Signaling

A shared line is an address of record managed by a call server. The server allows multiple end
points to register locations against the address of record.

The handset supports shared call appearances (SCA) using the SUBSCRIBE-NOTIFY method
in the “SIP Specific Event Notification” framework (RFC 3265). The events used are:



“call-info” for call appearance state notification



“line-seize for the handset to ask to seize the line

Summary

Parameter

Used to:

reg.x.address

specify the shared line address.

reg.x.type

specify the line type as shared.

reg.x.*

specify barge-in capabilities and line-seize subscription period if using
per-registration servers. A shared line will subscribe to a server providing
call state information.

call.shared.*

disable call diversion, expose auto-holds, resume with one touch, or play
a tone if line-seize fails.

voIpProt.SIP.specialEvent.lineSeize.no
nStandard

specify standard or non-standard behavior for processing a line-seize
subscription for mutual exclusion.

divert.x.sharedDisabled

specify per-registration whether diversion should be disabled on shared
lines.

Table 11-10: Shared Call Appearances

Parameter

Permitted Values

Default

call.shared.disableDivert

1

0 or 1

1

If set to 1, the diversion feature for shared lines is disabled.

Note:

This feature is disabled on most call servers.

call.shared.exposeAutoHolds

1

0 or 1

0

If 1, a re-INVITE will be sent to the server when setting up a conference on a shared line. If 0, no re-INVITE will be
sent to the server.

call.shared.seizeFailReorder

1

0 or 1

1

If set to 1, play re-order tone locally on shared line seize failure.

voIpProt.SIP.specialEvent.lineSeize.nonStandard

1

0 or 1

1

If set to 1, process a 200 OK response for a line-seize event SUBSCRIBE as though a line-seize NOTIFY with
Subscription State: active header had been received,. This speeds up processing.

divert.x.sharedDisabled

1

0 or 1

1

If 0, call diversion features can be used on shared lines. If 1, call diversion features are disabled on shared lines.

1

Change causes handset to restart or reboot.

«
...
250
251
252
253
254
...
»

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands