manualshive.com logo in svg

SpectraLink 8440, Administration Manual

Share
Download
SpectraLink 8440 Administration Manual Download Page 233

Spectralink 84-Series Series Wireless Telephones Administration Guide 

1725-86984-000_P.docx 
September 2016 

233 

Parameter 

Permitted Values 

Default 

reg.x.server.y.failOver.onlySignalWithRegistered 

0 or 1 

1 

 When set to 

1

, and the reRegisterOn and failRegistrationOn parameters are enabled, no signaling is accepted from 

or sent to a server that has failed until failback is attempted or failover occurs. If the handset attempts to send 
signaling associated with an existing call via an unregistered server (for example, to resume or hold a call), the call 
will end. No SIP messages will be sent to the unregistered server. When set to 

0

, and the reRegisterOn and 

failRegistrationOn parameters are enabled, signaling will be accepted from and sent to a server that has failed 
(even though fail

back hasn’t been attempted or failover hasn’t occurred).  

reg.x.server.y.failOver.reRegisterOn 

0 or 1 

0 

This parameter overrules the 

voIpProt.server.x.failOver.reRegisterOn

. When set to 

1

, the handset will 

attempt to register with (or via, for the outbound proxy scenario), the secondary server. If the registration succeeds 
(a 200 OK response with valid expires), signaling will proceed with the secondary server. When set to 

0

, the 

handset 

won’t attempt to register with the secondary server, since the handset will assume that the primary and 

secondary servers share registration information.  

reg.x.tcpFastFailover 

0 or 1 

0 

If 1, failover occurs based on the values of 

reg.x.server.y.retryMaxCount

 

or 

voIpProt.server.x.retryTimeOut

.  

 

Supporting 802.1X Authentication 

IEEE 802.1X is a port-based Network Access Control (PNAC). It provides an authentication 
mechanism to devices trying to attach to a local area network (LAN) or a wireless local area 
network (WLAN). IEEE 802.1X is based on the Extensible Authentication Protocol (EAP). 
Spectralink handsets support standard IEEE 802.1X authentication. 

Figure 10-1

 shows the 

RADIUS server using the AP as the authenticator for the Spectralink 84-Series handsets. 

Figure 10-1: A Typical 802.1X Network Configuration 

 

Spectralink handsets support the following EAP authentication methods: 

  EAP-PEAPv0/MSCHAPv2 (requires CA certificates) 

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands