SpectraLink 8440 Administration Manual Download Page 285

Page: 285 / 335

Spectralink 84-Series Series Wireless Telephones Administration Guide

1725-86984-000_P.docx
September 2016

285

Network Protocols and Ports Used on Spectralink
Handsets

See the next table for a list of the protocols and ports currently used by the Spectralink
Software.

Table 11-3: Protocols & Ports used by Spectralink handsets

Port Number

Protocol

Outgoing

Incoming

UDP or TCP

FTP

Provisioning, Logs

TCP

SSH

Admin

TCP

Telnet

Admin

TCP

DNS

UDP

DHCP

Server

UDP

DHCP

Client

UDP

TFTP

Provisioning, Logs

UDP

HTTP

Provisioning, Logs, Pull
Web interface, Poll

TCP

123

NTP

Time Server

UDP

389

LDAP

443

HTTPS

Provisioning, Logs

HTTP Pull Web interface, HTTP
Push

TCP

514

Syslog

Logs

636

LDAP

1719

H.323

RAS Signaling

1720

H.323

Signaling

2222

RTP

Media Packets

2223

RTCP

Media Packet Statistics

5060

SIP

SIP signaling

5061

SIP over
TLS

Secure signaling

5070

SIP

SIP signaling
(Nortel CS1K)

7778

OCS

14394

QBC
Signaling

QBC Server

TCP

24800

PDC

PDC Client messages

PDC Server messages

TCP

Telnet is disabled by default.

RTP and RTCP can use any set of even/odd ports between 2222 and 2269. This is configurable by setting

tcpIpApp.port.rtp.mediaPortRangeStart.

Summary of Contents for 8440
















































































































































































































































































































































Search results

Summary of Contents for 8440

Reviews:

Brands by name

Popular brands

SpectraLink 8440, Administration Manual

Search results

Summary of Contents for 8440

Reviews:

Brands by name

Popular brands