SpectraLink 8440 Administration Manual Download Page 152

Page: 152 / 335

Spectralink 84-Series Series Wireless Telephones Administration Guide

1725-86984-000_P.docx
September 2016

152

The Alarm event notifies an application that a (personal security) alarm condition has been
detected or cleared on the handset.

Use the following format when viewing the alarm event:

<PolycomIPPhone

<AlarmNotificationEvent

<PhoneIP

172.29.71.157</PhoneIP

<MACAddress

00907a0e4459</MACAddress

<BSSID

0023ebe4ebaf</BSSID

<StillAlarm

0</StillAlarm

<TiltAlarm

1</TiltAlarm

<RunningAlarm

0</RunningAlarm

<DuressAlarm

0</DuressAlarm

<TimeStamp

2012-12-10T08:11:25-07:00</TimeStamp

</AlarmNotificationEvent

</PolycomIPPhone

Where

Phone IP

is the IP address of the handset

MAC Address

is the MAC address of the handset

BSSID

is the MAC address of the AP the handset is currently using

StillAlarm

is the current state of this alarm detector 0 = no alarm, 1 = alarm

TiltAlarm

is the current state of this alarm detector 0 = no alarm, 1 = alarm

RunningAlarm

is the current state of this alarm detector 0 = no alarm, 1 = alarm

DuressAlarm

is the current state of this alarm detector 0 = no alarm, 1 = alarm

TimeStamp

is the recorded time of the event

Configuration Template

The PersonalAlarm.cfg template is provided with the software download in the Config

Features

folder. Use it to as a starting point to customize your deployment of this feature.

Summary of Contents for 8440
















































































































































































































































































































































Search results

Summary of Contents for 8440

Reviews:

Brands by name

Popular brands

SpectraLink 8440, Administration Manual

Search results

Summary of Contents for 8440

Reviews:

Brands by name

Popular brands