SpectraLink 80-Series Administration Manual Download Page 38

Page: 38 / 79

Spectralink 80-Series Handsets Administration Guide with SRP

1725-86030-000_G.docx
October 2013

Admin Menu Default Table

When the

Restore Defaults

option is selected, administrative parameters will be reset to their

factory defaults as shown in the table below. The

Telephony Protocol

setting will not change.

User parameters will be reset per the table on page 43.

Menu option

Setting

Sub-option

Sub-sub-option

Default

Phone Config

PTT/Emerg. Button

Emergency Dial

Disabled

PTT

Disabled

[if enabled]

Allowed Channels [all]

Name Channels

[none set]

Priority Channel

Disabled

Time Zone

GMT

Daylight Saving

DST No Adjust

Protected Spd Dial

[none set]

Password

Enabled

Change Password

[n/a]

Speakerphone

Enabled

Network Config

IP Addresses

Use DHCP

SSID*

[None set]

Security

None

Summary of Contents for 80-Series
















































































Search results

Summary of Contents for 80-Series

Reviews:

Related manuals for 80-Series

Brands by name

Popular brands

SpectraLink 80-Series, Administration Manual

Search results

Summary of Contents for 80-Series

Reviews:

Related manuals for 80-Series

Brands by name

Popular brands