SpectraLink 80-Series Administration Manual Download Page 68 | Manualshive

Page: 68 / 79

background image

Spectralink 80-Series Handsets Administration Guide with SRP

1725-86030-000_G.docx
October 2013

68

Message

Description

Action

Cert Invalid

When WPA2-Enterprise with PEAP
authentication is selected, the
wireless telephone failed to connect
to the network because the
certificate start date is in the future.

Verify that the NTP server is properly
configured with the correct time.
Verify that the certificates loaded on the
handset and authentication server have
valid start/end dates by looking at “valid
from” field from “validity” data in
certificates.
If any of the certificates have expired
replace them with new certificates.

Charging …

The handset is charging in the
Desktop Charger.

No action needed.

Charge Complete

The handset is now fully charged

No action needed.

Charger Error

The handset has detected a problem
with the charging circuitry.

Allow the charger and battery to cool. If
the problem persists, try a new or
confirmed battery. If the problem still
persists, contact technical support and
report the error.

Checking Code

Handset is contacting the Download
Master to determine if it has a newer
version of software that should be
downloaded.

None, this message should only last for
approximately one second. If message
remains displayed, power off and contact
customer support for a replacement
handset.

Checking DHCP IP

The handset is retrieving DHCP
information from the DHCP server.

None. This is informational only.

CRC Code Error

The software which has been TFTP
downloaded has a bad redundancy
code check.

Try the download again - it is possible the
software was corrupted during download. If
the error repeats, check that the download
image on the TFTP server is not corrupted.

Code Mismatch!

The software loaded into the
handset is incorrect for this model
handset.

Verify the License Management value is
correct. Replace the software image on the
TFTP server with software that is correct
for the handset model.

DCA Timeout

The handset has detected a fault for
which it cannot recover, possibly due
to a failure to acquire any network.

Turn the handset off, then on again. If error
persists, contact Spectralink Technical
Support and report the error.

DHCP Error (1-5)

DHCP Error 1

The handset cannot locate a DHCP server.
It will try every four seconds until a server
is located.

DHCP Error 2

The handset has not received a response
from the server for a request for an IP
address. It will retry until a server is found.

DHCP Error 3

The server refuses to lease the handset an
IP address. It will keep trying.

«
...
66
67
68
69
70
...
»

Summary of Contents for 80-Series
















































































Reviews:

No comments

Related manuals for 80-Series

Brand: Panasonic Pages: 722

Brand: Valcom Pages: 1

Brand: Valcom Pages: 13

Brand: Panasonic Pages: 80

Brand: VTech Pages: 31

Brand: Radio Shack Pages: 28

DECT2060-2 - DECT Cordless Phone

Brand: Uniden Pages: 56

Brand: BT Pages: 72

Brand: golmar Pages: 2

Brand: Serene Pages: 2

Brand: BT Pages: 80

Mobile Speakerphone P710e

Brand: Logitech Pages: 7

Brand: T-Mobile Pages: 191

Brand: Oricom Pages: 25

Brand: base engineering Pages: 26

Brand: TEH Pages: 11

Brand: Grundig Pages: 25

Brand: Motorola Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands