SpectraLink 80-Series Administration Manual Download Page 42

Page: 42 / 79

Spectralink 80-Series Handsets Administration Guide with SRP

1725-86030-000_G.docx
October 2013

Config menu 2nd level

3rd level

4th level

5th level

6th level

Push-to-talk*

Default Channel

Channel 1

….
Channel 24

Subscribed

Channels

Channel 1

Channel 2

Channel 3

Channel 4
….

Channel 24

PTT Audio

Volume

Audio Volume



PTT Tone Volume Tone Volume



PTT Vibrate

Disable/Enable

System Info

Phone IP Address

Gateway IP

Address

Firmware Version

Emergency Dial *

Emergency

Number
Emergency name

Push-to-talk

and

Emergency Dial

only appear if enabled.

When PTT Vibrate is enabled, the handset will vibrate three times whenever a PTT broadcast is received, whether the

handset is in standby or in a call. If in a call, the chirp alert will also sound.

Summary of Contents for 80-Series
















































































Search results

Summary of Contents for 80-Series

Reviews:

Related manuals for 80-Series

Brands by name

Popular brands

SpectraLink 80-Series, Administration Manual

Search results

Summary of Contents for 80-Series

Reviews:

Related manuals for 80-Series

Brands by name

Popular brands