SpectraLink 80-Series Administration Manual Download Page 69 | Manualshive

Page: 69 / 79

background image

Spectralink 80-Series Handsets Administration Guide with SRP

1725-86030-000_G.docx
October 2013

69

Message

Description

Action

DHCP Error 4

The server offered the handset a lease that
is too short. The minimum lease time is 10
minutes but Spectralink recommends at
least one hour minimum lease time. The
handset will stop trying. Reconfigure the
server and power cycle the handset.

DHCP Error 5

Failure during WEP Key rotation process
(proprietary feature).

DHCP Lease Exp.
yyy.yyy.yyy.yyy

y…y = DHCP Server IP address
DHCP is not responding to renewal
attempts (at least one renewal
succeeded).

The handset failed to renew its DHCP
lease, either because the DHCP server is
not running, or because the configuration
has been changed by the administrator.
The handset will attempt to negotiate a
new lease, which will either work, or
change to one of the above DHCP errors
(1-4).

DHCP NACK Error
yyy.yyy.yyy.yyy

y…y = DHCP server IP address
DHCP server explicitly refused
renewal.

The DHCP lease currently in use by the
handset is no longer valid, which forces the
handset to restart. This problem should
resolve itself on the restart. If it does not,
the problem is in the DHCP server.

DL not on sector

Handset software download files are
incorrect or corrupted.

Download new software from the
Spectralink site per Chapter 8

Software

Maintenance

.

DO NOT POWER
OFF

The handset is in a critical section of
the software update.

None. Do not remove the Battery Pack or
attempt to power off the handset while this
is displayed. Doing so may require the
handset to be returned to Spectralink to be
recovered.

Duplicate IP

The handset has detected another
device with its same IP address.

If using DHCP, check that the DHCP
server is properly configured to avoid
duplicate addresses.
If using Static IP, check that the handset
was assigned a unique address.

Erase Failed

Download process failed to erase
the memory in the handset. This
operation will retry.

Operation will retry but may eventually
report the error "int. error: 0F." Power cycle
the handset.

Erasing Memory

Handset has determined that a
download should occur and is
erasing the current software from
memory. This message also displays
a progress bar. When the progress
bar fills the display line the erase
operation is complete.

None. When the progress bar fills the
display line the erase operation is
complete.
Do not turn the handset off during this
operation.

«
...
67
68
69
70
71
...
»

Summary of Contents for 80-Series
















































































Reviews:

No comments

Related manuals for 80-Series

Brand: Saab Pages: 24

Brand: Uniden Pages: 46

Brand: FLORABEST Pages: 35

Brand: Radio Shack Pages: 24

Brand: TDS Pages: 8

Brand: NEC Pages: 57

Brand: invotel Pages: 2

Brand: 2N Pages: 32

Amplidect 295 SOS-Pro

Brand: Geemarc Pages: 2

Brand: Geemarc Pages: 31

Brand: Geemarc Pages: 58

Brand: Bosch Pages: 19

Brand: Bosch Pages: 18

Brand: Bosch Pages: 5

Brand: Bosch Pages: 36

Brand: Bosch Pages: 144

Brand: Bosch Pages: 146

Brand: Bosch Pages: 107

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands