Southwestern Industries TRAK 2OP M11, Safety, Installation, Maintenance, Service And Parts List

Page: 227 / 236

TITLE
SHEET
SIZE CODE IDENT. NO. DWG NO. REV
SCALE: OF
D
06238
NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A
CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH-
WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR
A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES
NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER
USE OF THIS INFORMATION WITHOUT THE WRITTEN CON-
SENT OF SOUTHWESTERN INDUSTRIES.
DATE APPROVALS
DRAWN BY
ENGINEER
CHECKER
FE MATERIAL
FINISH
INDEXER READY KIT
HARDINGE
28137
3 -
7/14/14 Chris
-
-
C
DIMENSIONS ARE IN INCHES
DEC. .X = ±.1, .XX = ±.01, .XXX = ±.005,
ANGLES .XX = ±0°30'
FRACTIONS = ±1/8
FINISH = 125 RMS
REMOVE ALL SHARP EDGES
MASK ALL TAPPED HOLES
DIMENSIONING PER ASME Y14.5
8/29/14 TO
8/29/14 Sal
REV ECN DATE APPRV DESCRIPTION
REVISIONS
B 14354 1-7-15 LG ITEM 16 26712 QTY 4 WAS: CLAMP-BALL LOCK QTY 1
A
B
C
D
A
B
C
D
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
THIRD ANGLE PROJECTION
SOUTHWESTERN INDUSTRIES, INC.
2615 HOMESTEAD PLACE
RANCHO DOMINGUEZ, CA 90220-5610
A 14201 8/29/14 TO PRODUCTION RELEASE
C 14448 11-13-15 PB
ADDED ITEMS 14,17,18, 24, 35, 36. REVISED PICTURES &
FIGURE NUMBERS.
ASSEMBLY PROCEDURE
I. TURN MACHINE OFF AND DISCONNECT MAIN AIR SUPPLY. OPEN ELECTRICAL CABINET & REMOVE ALL 3 REAR PANELS.
II. REMOVE RUBBER FEET FROM BOTTOM OF CONTROLLER (ITEM 1). REUSE SCREWS & ADD (4) FLAT & LOCK WASHERS (ITEMS 33 & 34) TO FASTEN CONTROLLER TO
BRACKET (ITEM 3). (FIG 1)
III. USE HARDWARE (ITEM 22, 31, 32) (4X) TO FASTEN BRACKET WITH CONTROLLER TO POST (ITEM 4). (FIG 6)
IV. USE ITEMS 19, 26, 27 (2X) TO FASTEN POST (ITEM 4) TO MACHINE. USE SPACER (ITEM 5) BETWEEN MACHINE AND POST.
(INSTALL TOP SCREW FIRST) (FIG 6)
VI. FASTEN FIXTURE PLATE (ITEM 2) TO MACHINE WORKTABLE USING BALL LOCK CLAMPS (ITEM 16). (FIG 1)
Va. USE HARDWARE (ITEMS 20, 28, 29) TO FASTEN FRONT OF INDEXER AND HARDWARE (ITEMS 21, 28, 29) TO FASTEN BACK OF INDEXER TO THE FIXTURE PLATE (ITEM 2). (FIG 2)
Vb. SCREW ITEM 10 INTO ITEM 9. INSERT 6mm AIR TUBING (ITEM 7) INTO ITEM 10. THEN CONNECT ITEM 9 TO HIGH FORCE COLLET OPTION AIR INPUT ON INDEXER. (FIG 2)
VII. ROUTE INDEXER MOTOR ENCODER AND POWER CABLES AND 6mm TUBING FROM INDEXER TO CONTROLLER. USE RUBBER STEEL LOOP (ITEM 15) TO SECURE BUNDLE IN 2 PLACES (FIG 3, 3a,3b). DRILL & TAP
#10-32 THRU VERTICAL ENCLOSURE BRACE WALL APPROXIMATELY 1" DOWN FROM CROSS BEAM & APPROXIMATELY IN THE MIDDLE OF THE BRACE AS SHOWN IN FIG
3a (DO NOT DRILL THRU OUTSIDE WALL). AT THE TOP OF THE ENCLOSURE (FIG 3b) REUSE EXISTING SCREW TO SECURE CLAMP.
VIII. ROUTE AC POWER EXTENTION CABLE , INDEXER INTERFACE CABLE (ITEM6) AND 6mm AIR HOSE THROUGH HOLE ON LEFT HAND SIDE OF MACHINE (FIG 5). ITEM 6 AND POWER CABLE WILL BE ROUTED UP TO
CONTROL BOX THROUGH RIGHT/FRONT GROMET (FIG 4a). PLUG 'INDEXER IN', 'INDEXER OUT' AND POWER CABLE TO RESPECTIVE AREAS (FIG 4, 4a, 4b). (FIG 5)
IXa. THEN SPLICE 10mm MAIN AIR TUBING AS SHOWN IN (FIG 7).
IXb. INSERT 10mm AIR TUBING INTO TEE ON BOTH ENDS AND 6mm AIR TUBING INTO TEE (ITEM 11). (FIG 7)
IXc. ROUTE THE INDEXER CONTROL BOX AC POWER CORD ALONG THE SIDE OF THE MACHINE USING ITEM 14 AND PLUG INTO THE EXTENTION CORD. CUT 6MM AIR LINE AND ADD ITEM 10 AND 18 TO MACHINE SIDE OF
AIR LINE AND ATTACH ITEM 9 AND 10 TO INDXER SIDE OF AIR LINE AND CONNECT THE TWO AIR LINES.
X. REINSTALL REAR PANELS & TURN MACHINE BACK ON.
XI. TURN ON AIR.
XII. TEST INDEXER FUNCTIONALITY.
3
11
7 REF
DETAIL OF AIR HOSE CONNECTION
TO INDEXER
MAIN SUPPLY LINE
(BEFORE TANK)
MAIN SUPPLY LINE
FIG 7
TO TANK