SOMFY animeo DRM Instructions Manual Download Page 30

Page: 30 / 47

animeo KNX 4 AC MoCo · REF. 5071074 -

30/47

Basic function

Selection options:



Venetian blind UP / DOWN



Switch/Dry contact



8-Bit value (rising edge)



Dimming

Longer operation (dimming) after

Selection options:



0.5 seconds



0.3 - 0.5 seconds

This parameter defines the activity time of the corresponding push button which makes a distinction between the sending of a switching

telegram and a dimming telegram. If the time, for example, is parametered on

0.5 seconds,

a dimming telegram is generated only after a

press activation longer than 0.5 seconds is made. With a pressing shorter than

0.5 seconds

a switch telegram is generated.

Input A/B

Selection options:



On/Off



Toggle/Toggle

This parameter defines the value which is transmitted with a short pressing of the corresponding input.



On/Off

With a short pressing of the push button at the input A, an "Off" telegram is generated. With a short activity of the corresponding push

button at the input B, an "On" telegram is generated. This function can be inverted by changing over the clamps at the inputs.



Toggle/Toggle

Switching over can be done with a short pressing of the push button at the input A or B. This means that the value which is in the corre-

sponding switching object is firstly inverted and is then transmitted.

On ("1")

Off ("0")

Toggle ("1/0")

"Push button binary input 1 ... 4"

Summary of Contents for animeo DRM
















































Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands

SOMFY animeo DRM, Instructions Manual

Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands